Ways to Fix a Running Toilet Quickly
That constant sound of water trickling in your bathroom gets old fast. It’s annoying when you’re trying to sleep, and it’s wasteful when you think about the water going down the drain.
A running toilet can waste hundreds of gallons per day, which shows up on your water bill eventually. The good news is that most running toilet problems have simple fixes you can handle yourself without calling a plumber.
Check the flapper first

The flapper is that rubber seal at the bottom of the tank that lifts when you flush. Over time, it gets worn, warped, or covered in mineral deposits.
Take the lid off your toilet tank and look at it while the toilet is running. If you see water flowing from the tank into the bowl, the flapper isn’t sealing properly.
Press down on the flapper with your hand. If the running stops, you’ve found your problem. Flappers are cheap—usually under ten dollars at any hardware store.
Turn off the water supply to the toilet, flush to empty the tank, unhook the old flapper from the chain and side ears, and snap the new one into place. The whole process takes about five minutes.
Adjust the chain length

The chain connecting the flush handle to the flapper needs to be just right. Too much slack and the flapper won’t lift fully when you flush.
Too tight and the flapper can’t seal properly after flushing, which causes continuous running.
Look inside the tank and check the chain.
It should have about half an inch of slack when the flapper is closed. If it’s too long, shorten it by moving the hook to a different chain link.
If it’s too short, you’ll need to add a link or two. Some chains have adjustable clips that make this even easier.
Inspect the fill valve

The fill valve controls water flowing into the tank after each flush. When it malfunctions, water keeps running even after the tank fills.
You’ll hear a hissing sound from the tank, and you might see water flowing into the overflow tube.
Try adjusting the float height first.
There’s usually a screw or clip on the fill valve that lets you raise or lower the water level. Lower it slightly and see if the running stops.
If the adjustment doesn’t work, you might need to replace the fill valve entirely. These cost around fifteen to twenty dollars and come with installation instructions.
Clean mineral buildup

Hard water leaves mineral deposits on toilet parts over time. These deposits prevent proper sealing and movement.
Take a close look at the flapper, the valve seat where the flapper sits, and the fill valve.
You can clean minor buildup with white vinegar and an old toothbrush.
For stubborn deposits, use a plastic scraper or sandpaper to gently remove them. Be careful not to damage rubber parts. Sometimes cleaning these surfaces is all you need to stop the running.
Replace a warped flapper

Flappers deteriorate even without visible cracks. The rubber gets stiff or warps from constant water exposure and chemical cleaners.
A warped flapper won’t create a proper seal, no matter how clean everything else is. When buying a replacement, bring your old flapper to the store to match the size and style.
Some flappers are universal, but getting the exact match works better. The packaging usually shows which toilet brands and models each flapper fits.
Fix the flush handle

A loose or sticky flush handle keeps the flapper open longer than necessary. Jiggle your flush handle. If it sticks in the up position, that’s why your toilet runs.
Tighten the nut on the inside of the tank that holds the handle in place. This nut has reverse threading, so you turn it counterclockwise to tighten.
If the handle still sticks after tightening, replace it. Handles cost less than ten dollars and can be swapped out in minutes.
Check the overflow tube

The overflow tube is the vertical pipe in the center of your tank. If water flows continuously into this tube, your fill valve isn’t shutting off properly.
The water level in the tank shouldn’t reach the top of the overflow tube. Mark the current water level with a pencil when the tank is full.
Wait an hour and check again. If the level has risen, your fill valve needs adjustment or replacement. If the water level is already at or above the overflow tube, adjust your float down immediately.
Test the refill tube

The small plastic refill tube clips onto the overflow tube and adds water back to the bowl after flushing. If this tube has come loose or is positioned wrong, water might continuously flow into the overflow tube.
Make sure the refill tube is securely clipped to the overflow tube and pointing down into it. The tube shouldn’t be pushed down inside the overflow tube—it should just rest at the top.
Repositioning this tube takes seconds and sometimes solves the problem entirely.
Replace the entire flush valve assembly

Sometimes the valve seat, where the flapper sits, gets so corroded or damaged that no new flapper will seal properly. If you’ve tried everything else and water still leaks from the tank to the bowl, you might need to replace the entire flush valve assembly.
This is a bigger job that requires removing the tank from the bowl. It’s still doable for someone handy, but it takes more time and effort.
The assembly costs between twenty and forty dollars and comes with detailed instructions. You’ll need an adjustable wrench and maybe a helper to lift the tank.
Address water pressure issues

Unusually high water pressure can prevent fill valves from shutting off completely. If your home has very high water pressure, it affects more than just your toilet.
Check other faucets in your house. If water comes out with intense force everywhere, you might need a pressure-reducing valve installed on your main water line.
This is one situation where calling a plumber makes sense, as it affects your entire plumbing system.
Clean the fill valve screen

Most fill valves have a small screen or filter at the water inlet that catches debris. Over time, sediment clogs this screen and prevents the valve from shutting off properly.
Turn off the water supply and flush the toilet to empty the tank. Find the fill valve and look for a small cap on the side where water enters.
Remove this cap carefully—it might have a screen attached. Rinse the screen under running water to remove sediment, then put everything back together.
Adjust the float

Older toilets often have a large float arm with a round float attached. If this float sits too high, the tank overfills and water runs into the overflow tube.
Bend the float arm down slightly to lower the water level in the tank. For newer toilets with a cylindrical float that slides up and down the fill valve, there’s usually an adjustment clip.
Pinch the clip and slide the float down about an inch. Make small adjustments and test after each one until the running stops.
Replace deteriorated washers

Inside the flush handle mechanism and around the fill valve, small rubber washers create watertight seals. These washers dry out and crack over time, causing leaks that make your toilet run.
Take apart the handle mechanism and the base of the fill valve to inspect these washers. Bring the old washers to a hardware store to find matching replacements.
A package of assorted washers costs just a few dollars and can fix multiple potential leak points.
Check for cracks in the overflow tube

The overflow tube itself can crack, especially if someone has over-tightened parts during previous repairs. Water leaking from cracks in this tube will cause continuous running.
Inspect the entire length of the overflow tube for any visible cracks or damage.
If you find cracks, you’ll need to replace the flush valve assembly since the overflow tube is part of that unit. Trying to patch a cracked overflow tube doesn’t work long-term.
When simple fixes lead to lasting quiet

You don’t need to live with that annoying running sound or the guilt of wasted water. Most toilet running issues come down to worn-out parts that cost less than a fancy coffee to replace.
Spending twenty minutes investigating and fixing the problem saves money on your water bill and gives you the satisfaction of handling it yourself. The quiet that follows a successful repair is worth every minute of effort.
More from Home As We Make It

- 18 Affordable Places to Retire in the U.S.
- Antique Glassware That’s Worth Collecting
- Stay-At-Home Jobs That Actually Pay
- 18 Forgotten Snacks from the ’80s and ’90s
- 20 Things That Make a House Look Cleaner Than It Is
Like Home As We Make It‘s content? Follow us on MSN.
