29 Fall Home Maintenance Tasks People Forget
Raking gets all the attention in October. The jobs that prevent a flooded basement, a frozen pipe or a 2 a.m. alarm chirp tend to sit quietly behind an appliance or above the ceiling, where nobody looks until something fails.
Most of them take less than an hour and cost very little. Skipping them is rarely dramatic at first, which is exactly why they get skipped.
Dryer Vent Ducts Collect What the Lint Screen Misses

Lint screens catch only part of what comes off a load of laundry. The rest travels into the duct and settles in the elbows and at the exterior hood.
The National Fire Protection Association has identified failure to clean as the leading factor in home dryer and washer fires, and US fire safety guidance generally calls for cleaning the duct at least once a year. Fall suits the job because heavy bedding and winter layers are about to arrive.
Warning signs include loads that need two cycles, a laundry room that runs hot and an outside flap that barely lifts. Rigid or semi-rigid metal duct is the accepted standard, since thin foil and plastic flex duct sag and trap lint.
Garden Hoses Left Attached to Outdoor Faucets

Water expands by roughly 9 percent as it freezes, and a hose left on the spigot keeps water trapped where it can do damage. Even a frost-free sillcock, which closes its valve several inches inside the heated wall, only drains if the hose comes off.
When the trapped water freezes, the pipe can split inside the wall, and the leak often stays hidden until the faucet is opened in spring. Homes with a separate interior shutoff for each outdoor line get the best protection when that valve is closed and the outside faucet is then opened to drain.
Hoses last longer drained and coiled indoors anyway.
Furnace Filters Go Unchanged Until the Heat Struggles

A clogged filter chokes the airflow a furnace depends on. With less air crossing the heat exchanger, the unit runs hotter, cycles off on its high-limit switch and works longer to reach the set temperature.
Common 1-inch pleated filters usually need checking monthly and replacing every one to three months during heavy use, while thicker 4-inch and 5-inch media filters often last six months or more. The arrow printed on the frame points toward the blower.
Households with pets, recent renovation dust or a wood stove tend to load filters faster than the package suggests. Writing the installation date on the cardboard edge removes the guesswork.
Humidifier Pads Hardened by Last Winter’s Minerals

Central humidifiers mounted on the furnace ductwork rely on an evaporator pad, sometimes called a water panel, that water trickles across while warm air passes through. Over a heating season the pad crusts with mineral scale, especially in hard-water areas, and a crusted pad adds little moisture while encouraging mold.
Manufacturers typically call for a new pad once a season, and the part often costs about 10 to 25 dollars. Bypass models also have a damper that needs to be moved to its winter position.
Indoor humidity between about 30 and 50 percent is the usual target, with the lower end safer in severe cold to limit condensation on windows.
Ceiling Fans Still Spinning in Summer Mode

Nearly every ceiling fan has a small direction switch on the motor housing, and many newer ones put it on the remote. In summer the blades turn counterclockwise, as seen from below, to push a breeze downward.
In winter the usual advice is clockwise at the lowest speed, which pulls air up and nudges the warm layer pooled at the ceiling back down along the walls without creating a draft. The effect is most noticeable in rooms with high or vaulted ceilings.
Savings claims vary widely and deserve some skepticism, but the comfort difference is real. The switch is also a good excuse to wipe a season of dust off the blades.
Smoke Alarms Carry a Manufacture Date on the Back

Batteries get the reminders, yet the alarm itself wears out. The National Fire Protection Association recommends replacing every smoke alarm 10 years after its date of manufacture, which is printed on the back or side of the unit, because the sensor becomes less reliable with age.
Pressing the test button monthly is the standard advice, and it takes seconds. US guidance places alarms inside each bedroom, outside each sleeping area and on every level, including the basement. Newer units often have sealed batteries meant to last the full decade.
An alarm that has yellowed, lacks a legible date or chirps after a fresh battery has likely reached the end of its service.
Carbon Monoxide Alarms Have Shorter Lives Than Expected

Carbon monoxide has no smell or color, and the heating season is when furnaces, boilers, gas water heaters and fireplaces all run at once. CO alarms do not last indefinitely.
Service life depends on the manufacturer and is commonly somewhere between five and 10 years, and most current models sound an end-of-life signal that a new battery will not silence. The date and replacement instructions are printed on the unit.
US safety agencies recommend an alarm on every level and outside each sleeping area, and many states require them in homes with fuel-burning appliances or attached garages. Fall testing catches a dead unit before the furnace begins its long run.
Water Heater Tanks Fill With Sediment From the Bottom

Minerals in the water supply settle on the floor of a tank water heater, forming a layer that insulates the water from the burner or lower element. Popping and rumbling during heating are the classic signs.
Many manufacturers recommend draining or flushing the tank about once a year, following the manual, with the gas control set to pilot or the electric breaker off first. A caution applies to old tanks that have never been drained, since a neglected drain valve can clog or fail to reseal, and a plumber may be the wiser choice.
US consumer safety guidance generally favors a setting of about 120 degrees Fahrenheit to limit scald risk.
Chimneys Need an Inspection Before the First Fire

Every wood fire leaves creosote on the flue walls, a combustible residue that is the fuel for chimney fires. The national standard on the subject, NFPA 211, calls for chimneys, fireplaces and vents to be inspected at least once a year and cleaned as needed, and the guidance applies whether the fireplace saw two fires or 50.
Gas fireplaces and furnace flues count too, since a blocked vent can send carbon monoxide indoors. A certified chimney sweep typically charges somewhere around 150 to 350 dollars for a basic inspection and cleaning.
A metal cap with mesh sides keeps out rain, nesting birds and squirrels, and it is far cheaper than repairing water damage inside the flue.
Gutters Get Cleaned Once and Downspouts Get Ignored

One inch of rain on 1,000 square feet of roof produces roughly 600 gallons of water, and all of it leaves through the downspouts. Many homeowners clean gutters in early fall and then skip the second pass after the last leaves drop, which is when the clogs actually form.
The bigger oversight sits at ground level. A downspout that empties beside the foundation saturates the soil against the basement wall, so extensions or splash blocks that carry water several feet away, commonly at least 4 to 6 feet, do more good than spotless gutters.
Clogged gutters in cold regions also feed ice buildup along the eaves.
Weatherstripping Flattens Long Before Anyone Notices

Foam tape and vinyl seals around doors and operable windows compress a little more each year until they stop springing back. A simple check is to close a door on a strip of paper. If the paper slides out with no resistance, the seal is not touching.
Daylight visible around a closed exterior door tells the same story. Replacement materials are inexpensive, usually under 20 dollars per door, and include adhesive foam, V-shaped spring strips and screw-on door sweeps for the gap at the sill.
Air leaks matter beyond the heating bill because moving air carries moisture into wall cavities, where it condenses on cold surfaces.
Exterior Caulk Cracks Where Trim Meets Siding

Sealant around window and door trim dries, shrinks and pulls away after years of sun. Those thin cracks let wind-driven rain reach the sheathing and the wood behind the paint.
Fall is the practical deadline because many caulks need temperatures above roughly 40 degrees Fahrenheit to cure, though labels differ and some products are rated for colder work. Gaps wider than about a quarter inch generally call for foam backer rod before sealant.
One mistake is worth avoiding. The small weep openings at the bottom of window frames and in brick veneer exist to let water out, and sealing them traps moisture inside the wall.
Sump Pumps Sit Idle and Seize

Months without rain can leave a sump pump untested right before the wet months return. The standard test is slow and simple: a bucket of water poured into the pit until the float rises should trigger the pump, which should empty the basin and shut off.
Homeowners also look at the discharge line outside, confirming that it is clear, pitched to drain and aimed away from the foundation, since a line that holds water can freeze solid. Pumps are mechanical and commonly last around seven to 10 years, though usage varies a great deal.
A battery backup unit earns its price in storms, when heavy rain and power outages tend to arrive together.
Sprinkler Lines Sit Shallow Enough to Freeze

Irrigation pipe is usually buried only several inches to a foot deep, well within the zone that freezes in cold climates. Water left inside can crack fittings, valves and sprinkler heads, and the damage stays invisible until the system is pressurized in spring.
In regions with hard freezes the usual remedy is a blowout, in which compressed air pushes water out one zone at a time. Too much air pressure can damage pipe and heads, which is why many homeowners hire an irrigation contractor, often for about 75 to 150 dollars.
The backflow preventer mounted above ground is typically the most exposed and most expensive part to replace.
Attic Insulation Settles and Blocks Its Own Vents

An attic tells a lot in a five-minute look. If the tops of the floor joists are visible, the insulation is almost certainly below current recommendations, which in much of the US fall between about R-38 and R-60.
Just as important is airflow. Insulation pushed into the eaves can smother the soffit vents, and a poorly ventilated attic stays warm enough to melt roof snow, which refreezes at the cold edge and forms ice dams.
Plastic or foam baffles keep that channel open. Dark stains on the underside of the roof deck, frost on nail tips in winter and a bathroom fan duct that ends in the attic all point to moisture trouble.
Roof Flashing Fails Before Shingles Do

Leaks tend to begin at the interruptions in a roof, where metal flashing seals the joints around chimneys, skylights, valleys and walls. A pair of binoculars from the yard is enough to spot lifted or rusted metal, missing sealant and shingles that have slipped.
Plumbing vent pipes deserve a close look, since the rubber collar around each one dries and cracks in the sun well before the surrounding shingles wear out. Replacing a cracked vent boot is a small repair. Ignoring it means a slow stain on a bathroom ceiling in February.
Anything that requires walking a steep or wet roof is best left to a roofer.
Branches Hanging Over the Roofline

Limbs that touch or overhang a roof cause trouble in three ways. They scrape protective granules off asphalt shingles in the wind, drop leaves directly into gutters and give squirrels and raccoons an easy bridge to the attic.
Under wet snow or ice, a weak limb can come down on the house. Arborists commonly suggest keeping branches several feet clear of the roof, with 6 to 10 feet often cited.
Late fall, after leaf drop, makes the branch structure easier to see and is a good pruning window for many species. Anything near a power line belongs to the utility or a qualified line-clearance crew, and large limbs call for a professional.
Lawn Mowers Stored With Untreated Gasoline

Gasoline does not keep well. Over a few months it oxidizes and leaves gummy deposits, and ethanol blends also absorb moisture from the air. A mower parked in November with a half tank is a common reason for a spring trip to the repair shop with a clogged carburetor.
Owner’s manuals generally offer two acceptable routes. One is running the engine until the tank and carburetor are dry.
The other is adding fuel stabilizer to fresh gas and running the engine for several minutes so treated fuel reaches the carburetor. The same care applies to trimmers, leaf blowers and pressure washers, and fall is a sensible time for an oil change and blade sharpening.
Window Wells Become Leaf-Filled Basins

Below-grade basement windows sit in metal or plastic wells that are supposed to drain through a gravel bed at the bottom. Leaves and silt clog that gravel, and in a heavy rain the well fills like a bucket until water presses against the glass and seeps over the sill.
Clearing debris by hand takes minutes. Inspectors also look for gravel that sits a few inches below the window sill and for soil that slopes away from the well’s rim.
Clear plastic covers keep leaves out, with one caveat: a well serving an egress window in a basement bedroom has to remain easy to open from inside under US building codes.
Soil Around the Foundation Slowly Tilts the Wrong Way

Backfilled soil next to a house settles for years, and garden beds, edging and mulch can gradually create a trough that holds rain against the wall. US residential building codes generally call for the ground to drop about 6 inches over the first 10 feet from the foundation.
A walk around the house during a steady rain shows where water is pooling. Low spots are best corrected with compacted, clay-rich fill soil, since loose mulch and sandy topsoil let water pass straight through.
Builders also keep the soil line several inches below the bottom of the siding so wood and sheathing stay dry and termites have no hidden path.
Refrigerator Coils Wear a Blanket of Dust

Refrigerators shed heat through condenser coils located underneath behind the front grille or on the back of the cabinet. Dust and pet hair insulate those coils, so the compressor runs longer and hotter to do the same work.
Cleaning once or twice a year with a long, narrow coil brush and a vacuum is a common recommendation, always with the unit unplugged first. Some newer models have enclosed condensers that the manual says need no routine cleaning, so a quick look at the documentation saves effort.
The timing matters in fall. Holiday cooking soon packs the refrigerator full and has the door opening constantly.
Range Hood Filters Saturated With Grease

Aluminum mesh filters under a range hood trap airborne grease, and a saturated filter stops catching it. Airflow drops, cooking odors linger and the grease film itself is flammable.
Most mesh and baffle filters slide out without tools and come clean after a soak in very hot water with degreasing dish soap and baking soda. Many are labeled dishwasher safe, though aluminum often discolors in the machine.
Recirculating hoods that do not vent outdoors add a charcoal filter that cannot be washed and typically needs replacing every few months, depending on how much frying goes on. Late fall, ahead of the heaviest cooking weeks of the year, is the obvious moment.
Storm Windows Stay Up in the Screen Position

Older homes with triple-track aluminum storm windows have a glass panel that slides down in place of the screen, and plenty of them stay raised all winter. Lowering the panel adds a second layer of glass and a pocket of still air, which cuts drafts and heat loss through single-pane sashes considerably.
The panels should latch fully into the side tracks. At the bottom of the storm frame are small weep slots that let condensation and stray rain drain out, and painting or caulking them shut leads to rotted sills.
Removable wooden storms deserve a glance at the glazing putty and paint before they go back up.
Garage Doors Leak Air and Run Dry

The largest moving object in most houses gets almost no upkeep. The flexible seal along the bottom edge hardens and cracks, letting in cold air, water and mice, and it slides out of a retainer channel for replacement on most doors.
Rollers, hinges and springs run quieter and last longer with a light coat of silicone or lithium-based garage door lubricant, while the tracks themselves are meant to stay clean and dry. Fall is also a good time for the reversal test.
A door with an automatic opener, closing on a two-by-four laid flat on the floor, should reverse on contact. Spring and cable repairs are dangerous and are left to trained technicians.
Hot Water Radiators Trap Air at the Top

In a hot water heating system, air works its way to the highest points and collects at the top of radiators. The symptom is a radiator that feels warm at the bottom and cool across the top, or one that gurgles.
Each unit has a small vent valve near an upper corner that opens with an inexpensive radiator key. With the heat switched off, the radiator cooled and a rag held underneath, the valve is opened slightly until the hiss of air gives way to a steady dribble of water, then closed.
Boiler pressure can dip afterward and is worth a glance at the gauge. Steam radiators are a different design with automatic air vents.
Outdoor Condensers Get Wrapped Too Tightly

Leaves, seed pods and grass clippings pack into the fins of an outdoor air conditioner over the summer, and clearing them along with about 2 feet of space around the cabinet helps airflow. The common mistake is a tight, full-length waterproof cover.
It traps condensation against the coil and wiring, which encourages corrosion, and it makes a dry, sheltered winter home for mice that chew insulation. HVAC technicians often suggest leaving the unit open or covering only the top to keep out falling debris and icicles. Heat pumps are another matter entirely.
They run all winter and are never covered, and snow drifts need to be kept clear of them.
Deck Boards Lose Their Water Repellency

Wood that soaks up water swells, and when that water freezes and thaws through the winter the boards check, crack and splinter. The test is a few drops of water sprinkled on the surface. Beads mean the finish is still working, while drops that darken the wood and vanish within a few minutes mean it is time to reseal.
Most sealers and stains need a clean, dry deck and a stretch of dry weather, often with temperatures above about 50 degrees Fahrenheit, so the window closes early in northern states. The same visit is a chance to confirm that the ledger board is firmly bolted to the house and that railings do not wobble.
Gaps That Invite Mice Indoors

Cooling nights send rodents looking for warmth, and they need very little room. A house mouse is commonly said to squeeze through a gap of roughly a quarter inch, about the width of a pencil.
Common entry points include the openings where gas lines, air conditioner lines and cables pass through siding, the bottom corners of garage doors and gaps under exterior door sweeps. Pest control professionals generally recommend packing openings with copper mesh or steel wool and then sealing over it, since mice chew through expanding foam used alone.
Firewood stacked against the house and bird seed stored in bags in the garage make the property more attractive than it needs to be.
Generators and Emergency Kits Tested Before the Storm

A portable generator that has sat since last winter may refuse to run when the power fails. Running it for several minutes with a load attached, checking the oil and stocking fresh stabilized fuel in an approved container are the usual fall steps.
The safety rules are firm. US safety agencies say a portable generator belongs outdoors only, at least 20 feet from the house with the exhaust pointed away, never in a garage, and it connects to household wiring only through a properly installed transfer switch or interlock. A basic kit adds flashlights, spare batteries, a battery or crank radio and about one gallon of water per person per day.
Frost Finds Whatever Was Put Off

Almost nothing on this list is difficult. The tasks are forgotten because the parts involved are out of sight and because a house gives very little warning before a small neglect turns into a repair bill.
Water and cold are patient, and they work on the same weak points every year.
A single weekend in October covers most of the work, and a short written checklist covers the rest. Homes that get this attention do not look any different from the street.
The difference shows up in January, when the furnace runs, the basement stays dry and the alarms stay quiet for the right reason.
More from Home As We Make It

- 18 Affordable Places to Retire in the U.S.
- Antique Glassware That’s Worth Collecting
- Stay-At-Home Jobs That Actually Pay
- 18 Forgotten Snacks from the ’80s and ’90s
- 20 Things That Make a House Look Cleaner Than It Is
Like Home As We Make It‘s content? Follow us on MSN.
